There is a decoration item in the decoration of the house which is the most troublesome and most need to pay attention to. It is the decoration of the wall surface, because the wall surface not only needs the structural stability to support the long-term use of the coating of the second wall decoration, but also needs to pay great attention. If we don't choose a better wall paint, it will affect the safety of our living. Let's let the decoration home network Xiaobian tell you about the wall decoration steps of the rough house . Please see the introduction of how to decorate the wall.
1. Check whether the wall is solid and flat is a step in the house inspection. Look at the wall is not strong, for cement wall, you can do this: find a hard object (such as a key, screwdriver, etc.), draw a stroke on the wall to see if it will draw a pit and slag serious. There are no shortcuts to finding cracks and holes, only carefulness + patience.
2, the kitchen and bathroom water is more, it is recommended that the facade wall is best tiling, the top wall is best to make a ceiling. These two methods of processing are not covered in this article. If you need to open them separately later.
3, the situation of the white wall, check whether the material is water resistant can be operated as follows: find a wall, splash a little water, rub it with your hand to see if it will become white pulp. If you can completely poke the white layer by hand, it is not water resistant. If you put a white color on your hand when you rub it by hand, but you can't destroy this layer of white material, it means that the material has certain water resistance. You can find a few more points to test it. If the hand is rubbed, the hand is almost white and not sticky, which means that the water resistance is very good.
4, white wall water resistance is not good, but for some reason (such as short-term living) are not willing to do the shovel wall treatment, you should do a good job of curing. For details on how to do this, see step 3.
5. In addition to water resistance, the empty drum situation is also a big problem that must be taken seriously. Now some developers use water-resistant materials (such as water-resistant putty), but the following uses inferior gypsum powder to make a thick leveling. It will not show long before the house will be cracked, and the time will be longer and even a whole piece will appear. Cracking. In the case of such an empty drum, it is best to shovel and redo!
6, check whether the old wall is strong: visually check whether there is peeling, cracking, drumming, if not, not strong; find a blunt device (such as a small hammer) knock on the wall, check if there is an empty drum, if not, it will not be strong; After the latex paint is polished off, pour some water and shovel it with a blade to see if it is easy to shovel. If it can be easily shoveled, it will not be strong.
How to decorate the wall surface - the steps to decorate the wall
1. If the shovel wall has been shoveled to the red brick layer, it is recommended to first make cement plastering. After the cement plastering is well cured, dry the wall and then seal the wall.
2. The hydropower transformation needs to be grooved on the wall. The remaining grooves are usually filled with cement mortar first, but there are not many that can be completely flat. At this time, it is best to start from the aspects of filling and cracking. Repair it with a repair gypsum product.
3. From the perspective of environmental protection, it is recommended not to use gypsum that needs to be mixed with glue. This should be taken care of when selecting products.
4. In particular, it is recommended to use self-adhesive kraft paper for cracking treatment when repairing cracks, slots, and holes. It takes little effort, but the effect is obvious.
5, the curing agent has liquid, such as various glue, concrete interface treatment agent (referred to as interface agent), but also dry powder, diluted with water can be used, such as dry powder curing agent. In terms of environmental protection, dry powders are generally less harmful.
6, the role of curing agent: the base layer is closed to prevent the next step of construction due to loose wall, floating soil or dry. Now the formal decoration company will first apply the curing agent on the original wall surface and then carry out the next step, which can prevent many problems caused by the wall base layer.
7, patch (kraft paper): is a more advanced way of sealing, the cost is higher, the general wall is not necessary to do. However, for insulated walls, loose walls, and cracked walls, the effect is more obvious and should be considered. If it has been applied (kraft paper), there is no need to make a curing agent, and the functions of the two have already coincided.
The above is how to decorate the wall surface. In Xiaobian, it seems that we want to solve the problem of how to decorate the wall. The first thing we need to do is to understand the things needed to decorate the wall. Serious and rigorous selection to achieve twice the result with half the effort, followed by the knowledge of how to decorate the wall. If you want to know more information, please continue to pay attention to the decoration home network.
More related wonderful reading:
Blank house wall decoration steps rough room wall decoration considerations
What is the wall decoration step? What is the wall decoration step of the rough house?
1.with 3000 square meter factory about 35 workshop workers and 25 office workers.
2.More than 20 sets of advanced machines with more than ten years domestic trade experience and international trade experience.
3.Manufacture and supply good quality automatic doors
4.With ISO 9001 Certification and many others certifications
5. Excellent DC brushless motor , high wear-resistant qualities wheels and reasonable structure design makes it more stable, quiet, longer life
6.Our Service system is perfect
Controller Dimensions : 85×124×600mm
Weight :12 kg
Maximun leaf weight :150 kg
Open range : 70°~115°
Closing speed : 10~43 cm/s
Door hold time :0.5~10 seconds
Main Power :AC 220V~250V,50~60 Hz
Maximum current :1A
Maximun motor power:55W
Wait Power :14W
Fuse :Minimum 3.5 ASlow
Operating Temperature : -30℃ ~+50℃
Swing Door,Exterior Swing Door,Aluminium Out Swing Door,Refrigerated Swing Door
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hongfadoor.com