The samba balloon is set up for lifting, revolving and self-rotating. Passengers can operate the center carousel by themselves to control the rotation of the cockpit! The ups and downs are between 1 and 1.5 meters.
Samba balloons are equipped with lifting, revolving and self-rotating. Passengers can operate the center carousel to control the rotation of the cockpit! The ups and downs are between 1m and 1.5m, similar to the spaceship rides in some parks. There are 8 large balloons, 8 bays below, and each bin can take 2-4 people. When running, it will rotate up and down, just like dancing samba. Therefore, call the samba balloon.
Samba balloon
Teach you the installation of the samba balloon for your play equipment:
1. Place the center frame on the pre-prepared hardened material, and then fix the bottom of the center frame with the expansion screw and the ground.
2. Prepare two layers of scaffolding. Then place the umbrella stand on the scaffolding. The small head is outward and the big head is placed inward. The umbrella frame label is then mapped to the center frame label. Then tighten with 18*100 screws. The remaining three umbrella stands are installed in the same way.
3. Connect the installed umbrella stand. The red circle is the tie rod connection position. In the middle position of the bottom of the umbrella frame, the tie rod is square steel (three in total) and fixed with 16*80 screws.
4. The boom installation position, the middle black point is the pin shaft, and the umbrella frame is installed with the boom pin hole.
5. Connect the installed boom to the cockpit. First place the cockpit directly below the boom, then lift the cockpit, pass the lower end of the boom through the screw hole in the center of the cabin, and then use the end of the boom through the cockpit. The type screws are tightened and the remaining two cockpits are fixed and fixed in the same way.
6. Install the center decoration on the center frame. First place the center decoration (glass reinforced plastic) on both sides of the center frame, then lift the center decoration to the height of the center disk, and then place the upper end of the center decoration and the bottom of the umbrella frame. The connection is connected with 12*50 screws, then the lower part is connected to the connection on the central large disc, and the other half of the center is installed in the same way. After the two center decorations are installed, the two pieces of decoration are internally connected by 12*50 screws, for a total of 8 screws.
7. Install the umbrella stand on the umbrella stand. First place the umbrella stand on the scaffold, then place the decoration on the side of the umbrella stand (the screen is facing outward), then fix it with self-tapping screws, average 20 A screw is used to prevent the trim from lifting, and then the other half of the umbrella frame is fixed in the same way. The remaining two umbrella stands are fixed in the same way.
8. Place the center top on the scaffold, then lift the center top, move it to the top of the center of the device, then slowly lower the center top, then insert the center point into the center connection hole.
9. Then pull the wire set on the center frame out of the equipment running radius of three meters, and then connect the control box terminal block position. (The specific wiring method is as described in the control box).
Playground Equipment:
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
With the continuous development of drilling production, the use conditions of drilling rigs have become more and more diversified, and various types of drilling rigs have appeared accordingly. Factors affecting the type and composition of drilling rigs include drilling method, drilling depth, borehole size and drilling tool size, and drilling area conditions (such as electricity or fuel, transportation, and meteorological conditions).
1. According to drilling method
(1) Impact drilling rigs, such as wire rope impact drilling rigs (drilling rigs), vibration drilling rigs, etc.
(2) Rotary drilling rigs, such as those used in rotary drilling.
(3) Downhole power drilling tools, such as rotary drilling tools, turbo drilling tools, screw drilling tools, electric drilling tools, etc.
2. Divided by drilling depth
(1) Ultra-deep well drilling rig. It adopts a drilling rig with a diameter of 114 mm drill pipe, a nominal drilling depth range of more than 7000 meters, and a maximum hook load of more than 4,500 kN.
(2) Deep well drilling rig. The drill rod is 114 mm in diameter, the nominal drilling depth is 4000-7000 meters or more, and the maximum hook load is 2250-4500 kN or more.
(3) Drilling rigs for medium and deep wells. It adopts a drilling rig with a diameter of 114 mm drill pipe, a nominal drilling depth range of 1500-4000 meters or more, and a maximum hook load of 900-2250 kN or more.
Three, according to power equipment
(1) Diesel Engine-driven drilling rigs, which use diesel engines as power through mechanical transmission or hydraulic transmission.
(2) AC driven drilling rig, suitable for use in oil fields with industrial power grids.
(3) The drilling rig is driven by direct current, and the working unit is driven by a direct current motor.
Fourth, according to the driving mode
(1) Drive alone. Each working machine is driven by generators of different sizes, which are mostly used for electric drive. The transmission is simple and easy to install, but the power utilization rate is low and the total equipment mass is large.
(2) Unified drive. The three working units of drawworks, drilling Pump and turntable are driven by the same power unit. Most drilling rigs use this scheme. The unified drive can also include only one drilling pump, and the other drilling pump is driven separately. The unified drive drilling rig has high power utilization and can be adjusted mutually when the engine fails, but the transmission is complicated, installation and adjustment are troublesome, and the transmission efficiency is low.
(3) Group drive. The combination of power is between individual drive and unified drive. There are two options for three working machines. The power utilization rate of this kind of drilling rig is higher than that of a single drive, and the transmission ratio is simple to drive in a unified manner. Two sets of working machines can also be installed on different heights and scattered sites.
Oil Drilling Rigs,Mine Drilling Rigs,Water Well Drilling Rigs,Exploration Drilling Rigs
Rugao Yaou Import & Export Trade Co., Ltd , https://www.ntyaoumachinery.com