Home>Bearing knowledge>Seven kinds of â€œsmall tipsâ€ for agricultural machinery repair and repair

/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131";

Seven kinds of "small tricks" for the repair of agricultural machinery

Source: China Bearing Network Time: 2013-06-10

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';

1. Cleverly installed cylinder. Winter; because the weather is cold; the water blocking ring becomes brittle; it is simply cracked when it is placed on the cylinder liner. Before the device; the water blocking ring can be immersed in warm water of about 60 Â°C for 5 minutes; The rear device is not easy to break.
2, cleverly installed rolling bearings. When installing rolling bearings; directly hit with a hammer; easy to deform the bearing; affect its service life. Now analyze a simple device approach: choose a 600 watt bulb to the power supply; use it to heat The bearing of the device; the heating time is 5 to 10 minutes; the heating temperature is maintained at about 110 Â° C; do not exceed 120 Â° C; then the bearing is agile on the shaft.
3. Cleverly repair the clutch pedal. The clutch pedal is smoothed after the horizontal stripes; when the pedal is pressed; the foot is easy to slip out. The rainy weather is easy to slip. If the upper and outer sides of the pedal are welded with a proper length of rebar; The pedal plane is 5 mm; it will not slip when used.
4, Qiaozhi tires slowly leaking. Take two tablespoons of talcum powder; remove the valve core; let the inner air be exhausted; use a hard paper to make a funnel into it; fill the talcum powder into the inner tube. Then install the valve core enough Gas; talcum powder is attached to the inner sidewall of the tire in a filled state; it can block small pores from leaking.
5. Remove dirt from the fine filter. The dirt and dirt in the rotor oil filter are not easy to remove. If you use a layer of paper on the inner wall of the rotor, let the soil adhere to the paper; remove the paper when protecting. The soil can be completely removed.
6. Check the cracks of the parts. Place the parts in the kerosene; take them out after a while; dry the surface and sprinkle a layer of white powder; then gently tap the parts with a small hammer; if there is a crack; The igniting oil that has been immersed in the crack is exuded from the crack; the crack is displayed on the white powder.
7. Cleverly disassemble the old cylinder liner. Use the old piston pin to load the old piston of the machine; install one or two old piston rings on the old piston; hook the old piston pin with a small steel bar with a diameter of 6.50 mm. The piston is reversely loaded into the cylinder; when the piston ring exceeds the lower edge of the cylinder liner; the cylinder sleeve is automatically bounced open; then the small steel bar is wound on the wooden stick; then the wooden stick is lifted; The missing sleeve can be removed.

Recommend to friends comments close window

Bearing related knowledge

The research and development of the thrust bearing and the method of stainless steel deep groove ball bearing The common sense of the analysis of the imported INA thrust ball bearing in the process of attention to the details of the industrial INA self-aligning ball bearing "protection strategy" large inventory solid mosaic self-smooth Bearing series features

This article links to http://
Please indicate the bearing network http://

Previous: How do you know the bearing?
Next: Common "NTN Bearing Equipment Challenges and Viewing Specifications"

Water Pump Part Series
1) Aluminum die casting part/Water Pump Part series
2) Water pump part series conforms to ISO9001 standard
3) Clients' drawings and samples are highly followed.
4) Machining all sorts of styles, according to customers' requirements
5) Strong R&D center design system and strict inspection processes to ensure the water pump part series quality.
6) Aluminum Die Casting suitable for communications, auto parts, lamp part series, water pump part series, power tool series, radiator part series, anti-static flooring products and Other Series Products.

Water Pump Part Series Production Flow:
Drawingsâ†’ mould making â†’raw casting â†’ sandblasting â†’rough machining or finish machining â†’surface treatment â†’product checkâ†’ packing â†’delivery strict

Our Advantage
(1) Ten years of experience in manufacturing and exporting water pump part series.
(2) OEM and custom-made service for water pump part series.
(3) All kinds of castings can be manufactured according to drawing, sample or specific industry standard.
(4) Strong engineering team makes high quality
(5) The coordinated service (casting, machining and surface treatment) make lower price possible.
(6) Advanced-level equipments.
(7) Full material testing process and quality control system.
(8) water pump part series quality warranty and on time delivery.

If you are interested, please contact us to talk about the details for water pump part series. You need to send us your drawing or sample to make mold first. Then we quote you price, if price accepted, we will open mold for you and send you sample before mass production.

Water Pump Part Series

Water Pump Part,Die Casting Water Pump Part,Aluminium Die Casting Parts

Ningbo Bowang Machinery Co.,Ltd , http://en.zjbwjx.com